Tabla De Contenido; Contents - Textron Ransomes Spider I Manual De Seguridad, Funcionamiento Y Mantenimiento

Operation manual - Spider ILD01

1 CONTENTS

1 CONTENTS ......................................................................................................................................................... 2
2 INTRODUCTION ............................................................................................................................................... 4
2.1 IMPORTANT ................................................................................................................................................. 4
2.2 MACHINE USAGE ....................................................................................................................................... 5
2.3 PROHIBITED USE ....................................................................................................................................... 5
2.4 PRODUCT IDENTIFICATION ...................................................................................................................... 6
2.5 GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS .................................................................. 7
3 SAFETY INSTRUCTIONS .................................................................................................................................. 8
4 SPECIFICATION ............................................................................................................................................... 11
4.1 SPECIFICATION ........................................................................................................................................ 11
4.2 NOISE EMISSIONS .................................................................................................................................... 11
4.3 CONFORMITY CERTIFICATES ................................................................................................................ 12
5 SAFETY DECALS ............................................................................................................................................. 13
5.1 INSTRUCTION DECALS .............................................................................................................................. 15
5.1 RECOMMENDED METODS OF OPERATION ............................................................................................. 16
6 CONTROLS ...................................................................................................................................................... 18
6.1 REMOTE RADIO CONTROLLER NBB ..................................................................................................... 18
6.2 REMOTE RADIO CONTROLLER HETRONIC .......................................................................................... 19
6.3 MOWER CONTROLS ................................................................................................................................. 20
7 DISPLAYS ......................................................................................................................................................... 21
7.1 NBB RADIO CONTROL DISPLAYS .......................................................................................................... 21
7.2 HETRONIC RADIO CONTROL DISPLAYS............................................................................................... 21
7.3 MOWER DISPLAYS ................................................................................................................................... 21
8 SAFETY SYSTEMS .......................................................................................................................................... 23
8.1 MOWER SAFETY SYSTEMS .................................................................................................................... 23
9. PREPARING THE MACHINE .......................................................................................................................... 24
9.1 MACHINE DELIVERY TO A DEALER OR RETAILER ............................................................................. 24
9.2 GEAR-BOX BY-PASS................................................................................................................................ 25
9.3 CHECKING ENGINE OIL LEVEL .............................................................................................................. 25
9.4 CHECKING HYDRAULIC DRIVE OIL LEVEL ........................................................................................... 26
9.5 PREPARING THE BATTERY .................................................................................................................... 26
9.6 FUEL TANK ................................................................................................................................................ 27
9.7 PREPARING THE NBB REMOTE RADIO CONTROLLER ...................................................................... 27
9.8 CHARGING THE NBB REMOTE RADIO CONTROLLER BATTERY ..................................................... 27
9.9 PREPARING THE HETRONIC REMOTE RADIO CONTROLLER .......................................................... 28
9.10 CHARGING THEHETRONIC REMOTE RADIO CONTROLLER BATTERY ......................................... 28
10 OPERATION ................................................................................................................................................... 28
10.1 TRANSPORTING THE MOWER ............................................................................................................. 28
10.2. STARTING THE ENGINE OF THE MOWER WITH THE NBB REMOTE CONTROL ........................... 29
10.2. STARTING THE ENGINE OF THE MOWER WITH THE HETRONIC REMOTE CONTROL ................ 30
10.3 SHUTTING OFF THE ENGINE ................................................................................................................ 31
10.4 EMERGENCY SHUTTING OFF OF THE ENGINE .................................................................................. 31
10.5 ENGAGING THE MOVING BLADES ....................................................................................................... 32
10.6 DISENGAGING THE BLADES ................................................................................................................ 32
10.7 HEIGHT OF CUT ADJUSTMENT ............................................................................................................ 32
10.8 DRIVING THE MACHINE ......................................................................................................................... 33
10.10 DRIVING ON SLOPES ........................................................................................................................... 34
10.11 STOPPING THE MACHINE ON A SLOPE ............................................................................................ 34
11 MAINTENANCE AND LUBRICATION ........................................................................................................... 35
11.1 MAINTENANCE CAHRT - MOWER ........................................................................................................ 35
11.2 MAINTENANCE CHART - ENGINE ......................................................................................................... 36
11.3 ENGINE MAINTENANCE ........................................................................................................................ 37
11.4 CLEANING THE FUEL TANK ................................................................................................................. 37
11.5 MAINTAINING THE HYDRAULIC DRIVE ............................................................................................... 37
11.6 CHECKING AND REFILLING OIL ........................................................................................................... 38
11.7 ADJUSTMENT OF THE NEUTRAL POSTION OF THE HYDRAULIC DRIVE ....................................... 38
11.8 DRIVE V-BELTS ....................................................................................................................................... 39
11.9 GEOMETRY ADJUSTMENT .................................................................................................................... 39
11.10 FINAL GEAR DRIVE TO WHEELS ....................................................................................................... 40
11.11 MAINTAINING ELECTRIC CIRCUITS AND DEVICES, TRANSMITTER ............................................. 40
11.12 ADJUSTING BLADE DECELERATION ................................................................................................ 40
11.13 CHAINS .................................................................................................................................................. 40
11.14 FUSES .................................................................................................................................................... 41
11.15 MOWING BLADE ................................................................................................................................... 42
2 / 54 rev. 07-01-01-2010