Descargar Imprimir esta página
Ocultar thumbs Ver también para EW4009:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

IMPORTANT!
Read all instructions before installing and using. Installer: This manual must be
delivered to the end user. ECCO is not responsible for the misuse of products by un-authorized personnel.
!
WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect! Check wattage
before installing light to avoid possible equipment damage.
Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency safety devices are essential to ensure the safety of you and those you are
seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,which can cause personal injury and/or
severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this safety device. Install this product so that output performance of the system is maximized and the controls
are placed within convenient reach of the operator so that s/he can operate the system without losing eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment area may reduce the effectiveness
of the air bag or become a projectile that could cause serious personal injury or death. Refer to the vehicle owner's manual for the air bag deployment area. It is the responsi-
bility of the user/operator to determine a suitable mounting location ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator should ensure the projection of
the safety signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people, vehicles or other obstructions.
7. The use of this or any other safety device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-of way for granted. It is your respon-
sibility to be sure you can proceed safely before entering an intersection, driving against traffic
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding warning signal devices. Therefore,
the user should check all applicable city, state, and federal laws and regulations. The manufacturer assumes no liability for any loss resulting from the use of this safety
device.
Note:
The product gets very hot to the touch after operating constantly for several hours.
Specifications:
Overall dimensions: 13" x 3" x 3.52"
Weight: 4.2 lbs. / 1.90 kg
Input Voltage: 12-24VDC
Temp. Range: -40° to 65°C
-40° to 150°F
Power Consumption for low beams (per light): 16.6W Max
Power Consumption for high beams (per light): 47W Max
Power Consumption for indicator light (per light): 6.8W Max
Power Consumption for parking light (per light): 0.55W Max
Power Consumption for low beams & high beams (per light): 53.76W Max
Power Consumption for low beams & high beams with lens heater (per light): 66.56W Max
Automatic lens heater turns on when ambient temperatures fall below(approximately) 35°F(2°C). The heater will turn off at a max
temperature of 154°F(68°C) when operating. The indicator LED will illuminate when the heater is active. The LED is located on the
inboard side of the light on the edge.
Installation Instructions:
Carefully examine the unit for damage before installation. If damage is found, contact the transit company or ECCO. Do not use broken
or damaged parts.
Prior to mounting, consideration should be given to cable location. The mounting location should be chosen such that there is maximum
visibility to the oncoming traffic.
Installation and Operation Instructions
EW4009 DOT LIGHT KIT
,
responding at a high rate of speed, or walking on or around traffic lanes.
Current Draw at 13.8VDC per light:
Low Beams: 1.36A Max
High Beams: 3.38A Max
Indicator Light: 0.84A Max
Parking Light: 0.52A Max
High & Low Beams: 4.20A Max
High & Low Beams with lens heater: 5.20A Max
Page 1 of 3

Publicidad

loading

Resumen de contenidos para Ecco EW4009

  • Página 1 Installation Instructions: Carefully examine the unit for damage before installation. If damage is found, contact the transit company or ECCO. Do not use broken or damaged parts. Prior to mounting, consideration should be given to cable location. The mounting location should be chosen such that there is maximum visibility to the oncoming traffic.
  • Página 2 Bracket Mounting: 1. Select a mounting location for the unit on a flat surface. 2. Secure the light head with the supplied hardware as shown in Figure 1. Adjust the beam angle as needed before ensuring all hardware is tightened. Aiming Instructions: Installer is responsible for ensuring the headlights are aimed properly such that beams comply with current highway regulations.
  • Página 3 Electronics Controls Company “ECCO” (Manufacturer) ECCO warrants that on the date of purchase, this product will conform to ECCO’s specifications for this product (which are available from ECCO upon request). This Limited Warranty extends for sixty (60) months from the date of purchase.
  • Página 4 ¡IMPORTANTE! Lea todas las instrucciones antes de la instalación y el uso del producto. Instalador: se debe entregar este manual al usuario final. ECCO no se hace responsable del uso incorrecto de los productos por parte del personal no autorizado.
  • Página 5 Compruebe cuidadosamente la unidad en busca de daños antes de la instalación. Si se detectan daños, comuníquese con la empresa de transporte o con ECCO. No utilice piezas rotas o dañadas. Antes del montaje, se debe tener precaución con la ubicación del cable. La ubicación de montaje se debe elegir de tal manera que tenga la máxima visibilidad para el tráfico en sentido contrario.
  • Página 6 Algunas jurisdicciones no permiten la exclusión ni la limitación de daños incidentales o consecuenciales. 833 West Diamond St Boise, Idaho 83705 Servicio al cliente EE.UU. 800.635.5900 Reino Unido +44 (0)113 237 5340 AUS +61 (0)3 63322444 www.eccoesg.com An ECCO SAFETY GROUP™ Brand www.eccosafetygroup.com 920-0781-00 Rev. C Página 3 de 3...
  • Página 7 EW4009 IMPORTANT! Lisez toutes les instructions avant l’installation et l’utilisation. Installateur : ce manuel doit être remis à l’utilisateur final. ECCO n’est pas responsable de l’utilisation abusive de ses produits par du personnel non autorisé. AVERTISSEMENT! Le non-respect des recommandations du fabricant lors de l’installation ou de l’utilisation de ce produit peut entraîner des dommages matériels et vous causer à...
  • Página 8 Instructions d’installation: Avant l’installation, vérifiez soigneusement que l’appareil n’est pas endommagé. En cas de dommage, contacter la société de transport ou ECCO. Ne pas utiliser de pièces brisées ou endommagées. Avant le montage, il convient de tenir compte de l’emplacement du câble. L’emplacement de montage doit être choisi de manière à assurer la visibilité...
  • Página 9 Certaines juridictions ne permettent pas l’exclusion ou la limitation des dommages indirects ou consécutifs. 833 West Diamond St Boise, Idaho 83705 Le Service Client États-Unis 800.635.5900 Royaume-Uni +44 (0)113 237 5340 AUS +61 (0)3 63322444 www.eccoesg.com An ECCO SAFETY GROUP™ Brand www.eccosafetygroup.com 920-0781-00 Rev. C Page 3 sur 3...