Página 1
OWNER’S MANUAL PORTABLE GENERATOR MODEL NUMBER P03611 Rev Level:00 IMPORTANT: Read all safety precautions and instructions carefully before operating equipment. Ensure engine is stopped and level before performing any maintenance or service. Record product information to reference when ordering parts or obtaining warranty coverage.
INTRODUCTION Thank you for purchasing a FIRMAN generator. Important Safety Information The manufacturer cannot possibly anticipate every possible circumstance that might involve a hazard. The warnings in this manual and the tags and decals affixed to the unit are therefore not all-inclusive.
CORRECT USAGE Example location to reduce risk of carbon monoxide poisoning • ONLY use outside and downwind, far away from windows, doors and vents. • Direct exhaust away from occupied spaces. INCORRECT USAGE Do not operate in any of the following locations: Near any door, window or vent Garage Basement...
Página 6
WHEN OPERATING EQUIPMENT WARNING • • DO NOT tip engine or equipment at angle which causes fuel to spill. • DO NOT stop engine by moving choke • control to “Start” position. WHEN TRANSPORTING, MOVING • OR REPAIRING EQUIPMENT • NEVER start or stop engine with electrical Transport/move/repair with fuel tank devices plugged in and turned on.
Página 7
• When using generator for backup power, WARNING notify utility company. Unintentional sparking • Use a ground fault circuit interrupter (GFCI) could cause fire or in any damp or highly conductive area, electric shock resulting such as metal decking or steel work. in death or serious •...
REMOVAL OF SHIPPING SUPPORTS Before you can run your new generator, follow these simple instructions: CAUTION 3. You may discard these brackets, as they are no longer Failure to remove these items can result required for normal operation of your generator. in damage to your generator, possible Your generator is now ready for use.
4- Choke Lever 12 - Control Panel 5- Fuel Valve 6- Air Filter 7- 208cc FIRMAN OHV Engine 8- Recoil Starter NOTE: *We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on this page.
Control Panel NOTE: Total power drawn from all receptacles must not exceed the name plate rating. Engine Switch – Flip the switch to the “ON”(l) 120V, 20A Duplex – (NEMA 5-20R) 20 Amp position and pull the recoil starter to start the of current may be drawn from this 120 Volt generator.
Página 12
SPECIFICATIONS Model P03611 Starting Watts 4550 3650 Running Watts Rated AC Voltage 120V Rated Fequency 60Hz Phase Single Voltage Regulator Power Factor Alternator Type Brushed Engine FIRMAN Engine Type Single Cylinder, 4-Stroke OHV Air Cooled Displacement 208cc Low Oil Shutdown...
4.Using oil funnel, slowly pour contents of Add Engine Oil provided oil bottle into oil fill opening to the "H" mark on dipstick. Be careful do not CAUTION overfill. Overfilling with oil could cause the engine to not start or hard starting. NOTE: Degrees Celsiusº(Outside) 5.Replace oil fill cap/dipstick and fully tighten.
Add Fuel Fuel must meet these requirements: • Clean, fresh, unleaded gasoline. • Use regular UNLEADED gasoline with the generator engine with a minimum 87 octane / 87 AKI (91 RON). For high altitude use, see "Operation at High Altitude". •...
THE GENERATOR (STATOR WINDING) AND THE Installation instructions are also available in the FRAME. Technical Bulletin area of the FIRMAN internet site. The part number and recommended minimum Connecting to a Building's Electrical System altitude for the application of the high altitude carburetor main jet is listed in the table below.
OPERATION • Generator Location WARNING Make sure you review each warning in order to • prevent fire hazard. Keep area clear of inflammables or other hazardous materials. Select a site that is dry, well ventilated and protected from the weather. •...
7. Pull the starter cord slowly until resistance is Starting the Generator felt and then pull rapidly. 1. Before starting the generator, check for loose or missing parts and for any damage which may have occurred during shipment. 2. Check oil level and fuel. 8.
Connecting Electrical Loads This unit has been pretested and adjusted to handle its full capacity. Before starting the generator, disconnect all load. Apply load only after generator is running. Voltage is regulated via the engine speed adjusted at the factory for Stopping the Engine correct output.
7. Repeat steps 5-6 for each additional item. 1.DO NOT try to restart the engine. 2.Contact an Authorized FIRMAN Service Dealer. 3.DO NOT operate engine until oil level is corrected. If oil level is below LOW mark on dipstick: 1.Add oil to bring level to HIGH mark.
• Use fresh and high quality lubricating oil to the ENGINE MAINTENANCE specified quantity. If contaminated or deteriorated oil is used or To prevent accidental starting, remove and the quantity of the engine oil is not sufficient, ground spark plug wire before performing any engine damage will result and its life will be service.
Spark Plug Maintenance Cleaning Fuel Strainer Changing the spark plug will help your engine Dirt and water in the fuel are removed by the fuel to start easier and run better. strainer. (a) Remove the spark plug cap. (b) Remove spark plug using provided wrench. (a) Remove the strainer cup and throw away water and dirt.
• DO NOT touch hot parts and AVOID hot exhaust CAUTION gases. • Failure to clean the spark arrester will result in Allow equipment to cool before touching. degraded engine performance. • Keep at least 5 feet (1.5 m) of clearance on all sides of generator including overhead.
Long Term Storage 8-Keep the engine switch and fuel valve on “OFF” position. It is important to prevent gum deposits from forming 9-Cover the unit and store in a clean, dry place in essential fuel system parts such as the carburetor, out of direct sunlight.
TROUBLE SHOOTING Problem Cause Correction 1. Circuit breaker is open. 1. Reset circuit breaker. 2. Fault in generator. 2. Contact authorized service facility. Engine is running, but no 3. Poor connection or defective cord 3. Check and repair. AC output is available. set.
1. Model No. ,Rev. Level and Serial No. and all of Purchase specifications shown on the Model No./Serial Contact the FIRMAN Service Center and FIRMAN No. plate. will troubleshoot any issue via phone or e-mail. 2. Parts number or numbers as shown in the If the problem is not corrected by this method, Parts List section.
Peoria, AZ 85381 Normal maintenance is not covered by this www.firmangenerators.com warranty. We are FIRMAN POWER - And we are here for you. Other Exclusions Customer Service Desk - 1-844-347-6261(1-844-FIRMAN1) This warranty excludes: 6am PST(9am EST) until 8pm EST(5pm PST) –...
If any such part fails during the period of warranty coverage, the part will be repaired or replaced by FIRMAN at no charge to the owner. Any such part repaired or replaced under the warranty will be warranted for the remaining warranty period.
Página 33
This Emission Control Systems Warranty shall not cover any of the following: (a) Consequential damages such as loss of time, inconvenience, loss of use of the engine or equipment, etc. (b) Diagnosis and inspection fees that do not result in eligible warranty service being performed. FIRMAN POWER EQUIPMENT INC. firmangenerators@sumec-na.com www.firmangenerators.com...
Página 34
Firman Power Equipment Inc. 8716 West Ludlow Dr. Suite #6 Peoria, AZ 85381 www.firmangenerators.com P/N:336745460 Rev 0 1...
MANUAL PARA EL PROPIETARIO DEL GENERADOR PORTÁTIL MODELO Nº P03611 Nivel rev:00 Lea detenidamente todas las instrucciones y precauciones IMPORTANTE: de seguridad antes de operar con el equipo. Asegúrese de que el motor está parado y nivelado antes de realizar ningún mantenimiento o servicio.
Página 36
Índice de Contenido Introducción ......1 Mantenimiento Y Almacenamiento..18 Precauciones De Seguridad .
Guarde estas instrucciones originales para consultas futuras. Este manual incluye el funcionamiento y el mantenimiento de los generadores FIRMAN. Toda información incluída en esta publicación está basada en la información de producción más actualizada disponible en el momento de la aprobación para impresión.
• SAFETY PRECAUTIONS PELIGRO Utilizar un generador en el interior PUEDE MATARLE EN CUESTIÓN DE MINUTOS. ADVERTENCIA NUNCA lo use en el interior Utilizar solo EN EL EXTERIOR de una casa o de un garaje, y lejos de ventanas, puertas y INCLUSO SI las puertas o las conductos de ventilación.
USO CORRECTO Ubicación ejemplar para reducir los riesgos de intoxicación por monóxido de carbono • lSOLO usarse en el exterior y en la dirección del viento, lejos de ventanas, puertas y conductos de ventilación. • Direccionar el tubo de escape lejos de espacios ocupados. USO INCORRECTO No utilizar en ninguno de los lugares siguientes: Cerca de una puerta, ventana o conducto de ventilación...
PONER EL EQUIPO EN FUNCIONAMIENTO ADVERTENCIA • NO ponga en funcionamiento este producto dentro de un edificio, garaje abierto, porche, equipamiento móvil, aplicaciones marinas o recintos cerrados. • NO incline el motor o el equipo hacia un ángulo que pueda hacer verter combustible. •...
• ADVERTENCIA Cuando utilice el generador como energía de reserva, notifique a la empresa eléctrica. • No usar un interruptor de circuito con falla a tierra (GFCI de las siglas en inglés) en ningun área húmeda o altamente conductora, como entablados de metal u obras de acero.
RETIRAR LOS SOPORTES PARA EL ENVÍO Antes de que pueda poner en marcha su nuevo generador, siga estas sencillas instrucciones: Los siguientes artículos deben ser retirados antes de poner en marcha su nuevo generador. Para proteger su generador, estos artículos han 2.
12 - Panel de control 4-Palanca del obturador 5-Válvula de combustible 6-Filtro de aire 7-Motor FIRMAN OHV 208cc 8-Interruptor de encendido de retroceso NOTA: Este modelo embarca desde la fábrica sin kit de ruedas. Para conseguir kit de ruedas y otros accesionarios, vísite a nuestra web www.firmangenerators.com o lláma a servicio de cliente...
Página 45
Control Panel NOTA: La potencia total recogida desde todos los receptáculos no debe ser superior a la potencia de la placa de identificación. Interruptor del Motor – Voltee el interruptor hacia la posición “ON”(l) y estire el interruptor de encendido de retroceso para encender el Dúplex 120V, 20A - (NEMA 5-20R) 20 Amps generador.
TORCH F6RTC/NGK BPR6ES/CHAMPION RN9YC MENSAJE IMPORTANTE SOBRE LA TEMPERATURA: Su Equipo de Potencia Firman está diseñado y catalogado para operaciones continuadas a una temperatura ambiente hasta los 40ºC (104ºF). Cuando sea necesario, su producto podría operar a temperaturas entre los -15ºC (5ºF) y los 50ºC (122ºF) por períodos cortos. Si el producto se expone a temperaturas fuera de este alcance durante el almacenamiento, se debería volver a su...
AÑDIR ACEITE AL MOTOR PRECAUCIÓN NOTE: Grados Centígradosº (exterior) 5. Vuelva a poner el tapón/varilla de nivel y Completamente Sintético 5W-30 asegúrelo completamente. 6. El nivel de aceite debería ser revisado antes de 5W-30 10W-40 cada uso o almenos cada 8 horas de funcionamiento. Realice un buen mantenimiento del nivel de aceite.
AÑADIR COMBUSTIBLE El combustible debe cumplir con los siguientes requisitos: • Gasolina limpia, nueva, y sin plomo. • Utilice gasolina SIN PLOMO regular con el motor del generador con un mínimo de 87 octanos /87 AKI (91 RON). Para un uso a gran altitud, lea “Funcionamiento a gran altitud”.
combustible en el aire. HAY UN CONDUCTOR PREMANENTE ENTRE EL GENERADOR (BOBINA DEL ESTÁTOR) Y EL MARCO. Conectar al Sistema Electrico del Edificio de carburador de gran altitud. ADVERTENCIA Altitud 208cc 335717002 3000-6000Pies Reactor principal de Altitud 1 335717003 Reactor principal de Altitud 2 6000-8000Pies •...
• FUNCIONAMIENTO Ubicación del Generador ADVERTENCIA hacia espacios ocupados. Asegúrese de repasar todas las advertencias para • prevenir riesgo de incendio. Mantenga el área alejada de materiales inflamables u otros materiales peligrosos. Escoja un lugar seco, bien ventilado y protegido el gas de monóxido de carbono.
Página 51
7. Tire lentamente de la cuerda de arranque hasta Starting the Generator que note resistencia, luego tira rápidamente. 1. Antes de arrancar el generador, compruebe que no haya partes sueltas, que falten o algún tipo de daño ocasionado durante el envío. 2.
Conexión de Cargas Eléctricas Parada del Motor eléctricos enchufados o conectados. PRECAUCIÓN Deje que el generador funcione sin carga unos minutos para estabilizar las temperaturas internas del motor y el generador. 1.Deje que el motor se estabilice y se caliente 2.
7. Repita los pasos 5-6 para cada dispositivo 2.Contacte con un Servicio Distribuidor autorizado adicional. de FIRMAN. 3.NO utilice el motor hasta que el nivel de aceite sea correcto. Si el nivel de aceite está por debajo de la marca LOW en la varilla medidora: 1.Añada aceite hasta llegar al nivel de la marca...
MANTENIMIENTO Y ALMACENAMIENTO PROGRAMA DE MANTENIMIENTO Cada 100 A diario (Antes Primeras Cada horas (o ITEM OBSERVACIONES de usar) 25 horas 50 horas anualmente) Comprobar el estado. Ajustar la √ Bujía separación y limpiar. Cambiar si es necesario. √ Comprobar el nivel de aceite. Aceite del motor √...
• MANTENIMIENTO DEL MOTOR Utilice lubricante nuevo y de alta calidad en la Para evitar el arrancado accidental, quite y ponga cantidad especificada. en el suelo el cable de la bujía antes de realizar Si se utiliza aceite contaminado o deteriorado o cualquier servicio.
Mantenimiento de La Bujía LIMPIEZA DEL FILTRO DE CARBURANTE Cambiar la bujía hará que su motor arranque Suciedad y agua en el carburante se eliminan con más facilidad y funcione mejor. mediante el filtro de carburante. (a) Quite el tapón de la bujía. (b) Quite el tapón de la bujía con la llave proporcionada.
• 4. Reemplace el apagachispas si está dañado. NO toque las parts calientes y EVITE los gases calientes de escape. 5. Posicione el apagachispas en el silenciador y • adjúntelo con los tornillos. Deje que el equipamiento se enfríe antes de tocarlo. •...
Almacenamiento de Largo Plazo 7-Retire la bujía y vierta aproximadamente una Es importante evitar que los depósitos de goma se formen cucharadita de aceite del motor a través del orificio en partes esenciales del sistema de combustible tales como de la bujía, tire del arrancador de retroceso varias el carburador, las mangueras de combustible o el tanque veces para distribuir el aceite para lubricar el cilindro.
LOCALIZACIÓN Y RESOLUCIÓN DE PROBLEMAS Problema Motivo Corrección 1. El cortacircuitos está abierto. 1. Reinicie el cortacircuitos. El motor funciona, 2. Desperfecto en el generador. 2. Contacte con instalación de servicio pero no hay ninguna 3. Mala conexión o conjunto de autorizado.
DIAGRAMA DE LAS PIEZAS Y LISTA DE PIEZAS P03611 DIAGRAMA DE LAS PIEZAS Spanish Servicio al Cliente: 1-844-FIRMAN1...
Página 61
FIRMAN 208cc DIAGRAMA DE LAS PIEZAS Spanish Servicio al Cliente: 1-844-FIRMAN1...
Página 62
P03611 LISTA DE PIEZAS Qty. Qty. Numero de Parte Descripción Numero de Parte Descripción 336713630 336713551 FIRMAN 208cc Motor Valvula de combustible 336713501 336713552 Enchufe de la cubierta frontal 2 Montaje de la funda externa del silenciador 336713502 336713553 Enchufe de la cubierta frontal 1...
FIRMAN 208cc Motor LISTA DE PIEZAS NO. Numero de Parte Qty. Descripción Qty. Descripción Numero de Parte 336723500 Montaje del cárter 336723553 Conjunto del carburador 336723501 336723554 Junta del filtro de aire Clavijas de posicionamiento Ø9×14 336723502 Sensor del nivel de aceite...
Garantía Limitada de Tres (3) Años FIRMAN Calificaciones de Garantía El GENERADOR FIRMAN registrará la garantía cuando reciba su Carta de Registro de Garantía y una copia de su recibo de compra de uno de los puntos de venta FIRMAN como comprobante de compra. Envíe su registro de garantía y el comprobante de compra en...
Peoria, AZ 85381 esta garantía. www.firmangenerators.com Otras Exclusiones Somos FIRMAN el poder - y estamos aquí para usted. Oficina de servicio al cliente - 1-844-347-6261 (1-844-firman1) Esta garantía excluye: 6 AM PST (9am est) hasta las 8pm EST (5PM PST) -Defectos cosméticos como la pintura, etiquetas,...
7) A lo largo del período de la garantía de las emisiones descrito en la subsección (b)(2), FIRMAN seguirá manteniendo un suministro de las piezas en garantía adecuadas para cumplir con la demanda esperada de estas piezas.
(a) Daños emergentes como pérdida de tiempo, molestias, pérdida del uso del motor o equipo, etc. (b) Los cargos por diagnóstico e inspección que no den como resultado un servicio calificado cubierto por la garantía. FIRMAN POWER EQUIPMENT INC. firmangenerators@sumec-na.com www.firmangenerators.com...
Página 68
Firman Power Equipment Inc. 8716 West Ludlow Dr. Suite #6 Peoria, AZ 85381 www.firmangenerators.com Todos los derechos reservados. Cualquier reimpresión o uso no autorizado sin la autorización por escrito queda explícitamente prohibido. P/N:336745460 Rev 0 1...