Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
6 2
EN
USER INSTRUCTIONS
1. TECHNICAL FEATURES
•
Power supply: 4 batteries type AA, LR6 or equiva-
lent (6 volts).
•
Codes from 3 to 8 digits +
enter
or
after entering the digits).
#
•
One user code, plus one emergency code, plus two
emergency keys.
•
Possible External power supply (F) (External battery
holder not included).
2. FIRST USE
2.1.
You will found the safe opened with the emer-
gency keys inside the plastic bag.
2.2.
If you fi nd some seal next to the bolts, please
remove it.
2.3.
Open and close the safe several times (section 3)
with the original codes.
2.4.
Program the original user code and the emergen-
cy code for your own ones (section 4).
3. OPENING/CLOSING INSTRUCTIONS
3.1.a.
Enter the code (
3.1.b.
After pressing each digit, the yellow light will
fl ash with a beep. If the code is correct, the green
light will turn on. Please turn the knob and pull out
to open.
3.2.
To close, push the door and turn the knob.
4. PROGRAMMING OR CHANGING THE CODES
4.1. Programming the user code
Every safe has been programmed with the same user
code:
1 2 3 4 5 6 #
not forget to change it.
4.1.a.
Open the safe with your user code.
4.1.b.
Press the green button inside the safe. The yel-
low led will light to indicate you must enter the new
code.
4.1.c.
Enter the new user code from 3 to 8 digits +
4.1.d.
Before closing the door, check the new code
at least 3 times, following the opening instructions.
Example of programming:
1 2 3 4 5 6 #
4.1.e.
4.1.f.
Green button.
3 1 8 7 7 0 #
4.1.g.
+
#
).
4.2. PROGRAMMING THE EMERGENCY CODE
4.2.a.
Open the safe with the user code.
0 0
4.2.b.
Enter
.
4.2.c.
Press the green button inside the safe. The yel-
low light will turn on and two beeps will be heard to
indicate you must enter the new code.
4.2.d.
Enter the new emergency code from 3 to 8 dig-
its +
.
#
4.2.e.
Before closing the door, check the new code.
or
(it's the same
#
).
1 2 3 4 5 6 #
. For your security do
(user code).
(introduce new user code
Example of programming:
1 2 3 4 5 6 #
4.2.f.
0 0
(Enter
4.2.g.
4.2.h.
Green button.
0 0 0 0 0 0
4.2.i.
code +
#
).
5. EMERGENCY OPENING
5.1.
2 emergency override keys, which will allow you
to open the safe in case of electronic anomaly. Please
take out the emergency lock cover, between the knob
and the keyboard. Insert the emergency key, turn it
and open the door.
VERY IMPORTANT:
Never keep the emergency keys in the safe.
5.2. Emergency code:
you have forgotten your normal opening code num-
ber. One you program your emergency code number
you can use it as you usually do with your user code.
5.3. An external power supply:
open the safe in case of discharged batteries and not
having an emergency key, to plugin an external power
supply in the connexion that is at the bottom of the
front panel (F). Then introduce your code number, and
open your safe as usual (not included).
6. OTHER FEATURES
• Wrong code:
low led will fl ash and you will hear the error tone.
• Blocking system:
wrong codes, the system will be blocked for 20
seconds. If you press 3 wrong codes again, the
system will be blocked for 5 minutes.
• Low batteries:
led lights with the green, that means the batteries
level is very low. You must change the 4 batteries
for 4 new alkaline ones.
.
#
• Replacement of batteries:
can be found in a compartment inside the door.
Once you have removed the cover, change all
FOUR batteries for new ones. Check the right func-
tioning of the 2 codes of the safe before locking it.
• Maintenance of the codes:
batteries, will remember the codes for 30 minutes.
If they are deleted, you will have to reprogam both
codes.
(user code).
0 0
).
#
(introduce an emergency
to open your safe in case that
would allow you to
If the code entered is wrong, the yel-
After entering consecutively 3
If when opening the door, the red
The batteries holder
The system, without
Publicidad
Tabla de contenido
