Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Installation Instructions:
Attaching Wall Mount to Studs:
1.
Locate a proper place to mount by using a quality stud finder
(Figure 1). Mark center of stud. It is recommended that the
center of the stud be used and that a nail be used to verify that
a stud has been located.
2.
Gently pull back vinyl cover at top of backplate to expose
plate. Hold mount up to wall and mark wall at top of mount
backplate at desired height. (Figure 2) (Set mount aside after
marking)
3.
Measure down stud from top of plate 2-5/8" and mark for first
screw. (Figure 3) and drill (3/16" x 3") deep pilot hole into wall
at mark
4.
Using Hex Key (Provided) screw (1) Hex Screw into pilot hole
leaving 1/8" gap to wall.
5.
Carefully cut cable tie holding motorized plate. (Figure 9)
6.
Place mount on screw using butterfly hole (second hole from
top).
7.
Level mount using Bubble Level and drill 2nd (3/16" x 3") deep
pilot hole through bottom hole in backplate. (Figure 7)
8.
Using Hex Key attach 2nd screw/washer combination (Do Not
Overtighten) (Figure 7)
9.
Drill 3rd (3/16" x 3") deep pilot hole through hole through top
hole in backplate. (Figure 8)
10.
Attach 3rd screw/washer combination (Do Not Overtighten)
(Figure 8)
11.
Using Hex Key tighten first screw (Do Not Overtighten)
Figure 1
Please Refer to Stud Finder
Instruction Manual
Figure 4
Figure 7
S
T
Bottom of Mount
Attaching Wall Mount to Concrete:
1.
Gently pull back vinyl cover at top of backplate to expose
plate. Hold mount up to wall and mark wall at top of mount
backplate at desired height. (Figure 2) (Set mount aside after
marking)
2.
Measure down from top of plate 2-5/8" and mark for first screw.
(Figure 3)
3.
Drill (1/2" x 3-1/8") deep hole into wall at mark (Figure 4)
4.
Insert Concrete Anchor flush with wall. (Figure 5)
5.
Using Hex Key (Provided) screw (1) Hex Screw into concrete
anchor leaving 1/8" gap to wall. (Figure 6)
6.
Place mount on screw using butterfly hole (second hole from
top).
7.
Level mount using Bubble Level mark two remaining mounting
holes on wall.
8.
Remove mount and drill at marks (1/2" x 3-1/4") deep holes.
9.
Insert concrete anchors until flush with wall.
10.
Carefully cut cable tie holding motorized plate. (Figure 9)
11.
Reinstall mount on single screw.
12.
Attach 2nd and 3rd screw/washer combination (Do Not
Overtighten)
13.
Using Hex Key tighten first screw (Do Not Overtighten)
Figure 2
Top of Mount
Figure 5
U
T
S
Figure 8
Top of Mount
Figure 3
Top of Mount Mark
2-5/8"
Figure 6
Figure 9
Attaching LCD/Plasma to Mounting Arms:
1.
Determine Correct bolt to attach TV to Mounting Arm.
Caution:
Carefully
thread
the
of your LCD to determine which bolt is to be used. If
there is any resistance remove the bolt immediately.
Select longest bolt that can be fully threaded into
Never
place
LCD/Plasma
down
on
any
surface
to
DO NOT OVERTIGHTEN BOLTS WHEN INSTALLING ARMS
ON TELEVISION.
2.
Install mounting arm to TV with Bolt, Lock Washer, and Flat
Washer for M4 or M5 Bolts. (Figure 10)
3.
Install mounting arm to TV with Bolt and Lock Washer
or M8 Bolts. (Figure 11)
Figure 10
M4 and M5 Bolts
Bags 1 or 2
Figure 11
M6 and M8 Bolts
Bags 3 or 4
bolt
into
the
back
TV.
screen
face
prevent
scratching.
for M6
(USE SPACER
ONLY IF
NEEDED)
(USE SPACER
ONLY IF
NEEDED)
www.LevelMount.com
1-888-229-1459
©2008 Level Mount
Patents Pending
Publicidad
Tabla de contenido
