Technical Data; Safety Instructions; Mains Connection - AEG H 500 Instrucciones De Uso

Ocultar thumbs Ver también para H 500:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 17

TECHNICAL DATA

Nominal power output ................................................................
Planing width ..............................................................................
Planing depth .............................................................................
Rabbet depth ..............................................................................
No-load speed ............................................................................
Weight without cable ..................................................................
Typical A-weighted sound levels:
Sound pressure level (K = 3 dB(A)) ..........................................
Sound power level (K = 3 dB(A)) ..............................................
Typically the hand-arm vibration is below 2.5 m/s
Measured values determined according to EN 60 745.
Wear ear protectors!

SAFETY INSTRUCTIONS

Please pay attention to the safety instructions in the attached
leaflet!
Wear ear protectors. Exposure to noise can cause hearing
loss.
Appliances used at many different locations including open air
must be connected via a current surge preventing switch.
Always use the protective shields on the machine.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes and
apron.
Sawdust and splinters must not be removed while the
machine is running.
Do not drill the housing, as the protective insulation would be
rendered ineffective. Use adhesive labels.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Before switching on ensure that protective swing guard moves
freely.
Only plane with sharp blades and avoid metal (nails, screws).
The protective swing cover and the blade drive cover on the
side must be easy to move to and fro.
The protective swing cover must not be locked open except
when the plane is beeing used in a fixed mounting.
Protective swing guard operation only with the provided lever
or automatically by the workpiece.
In the fixed position, the plane may only be used in the AEG
stationary mounting or in the AEG dressing and planing table.
Do not put the machine down until the blade drive has
stopped running.
Never reach into the danger area of the plane when it is
running.
The dust that arises when working with this tool can be
detrimental to health (e.g. when working oak or beech wood,
stones, paint, which could contain lead or other harmful
chemicals) and therefore not reach the body. Use a dust
absorption system and wear a suitable dust protection
mask. Remove deposited dust thoroughly, e.g. with a
vacuum cleaner.
SPECIFIED CONDITIONS OF USE
The plane can plane surfaces and rabetts, and bevel and
chamfer edges.
Do not use this product in any other way as stated for normal
use.

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also possible
to connect to sockets without an earthing contact as the
design conforms to safety class II.
15
ENGLISH
H 500
......... 500 W .....................750 W ......................800 W
........... 82 mm ..................102 mm ...................102 mm
....... 0-1,6 mm ................0-2,0 mm .................0-2,0 mm
........ 0-16 mm .................0-22 mm ..................0-22 mm
..... 17000 min
.......... 2,5 kg .....................3,5 kg .......................3,5 kg
........... 86 dB (A) ................87 dB (A) .................87 dB (A)
........... 97 dB (A) ................98 dB (A) .................98 dB (A)
.
2
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, EN 61000-
3-2, EN 61000-3-3, in accordance with the regulations 98/37/
EC, 89/336/EEC
ADVICE FOR OPERATION
Never reach into the danger area of the plane when it is
running.
Place the front page of the machine on to the worpiece and
switch on, before the planer blade touches the workpiece and
then guide evenly over the workpiece.
The selv opening swivel guard should be lifted only by the
workpiece or with the lever.
The v-shape notch in the front of the supporting plate ensures
safe chamfering of edges.
To adjust cutting depth first set on "P". Then adjust to the
necessary setting according to required chamfering depth.
When using the grooved planer blades, always use two
blades with a different number of grooves.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
If the shavings discharge is stained with resin, remove it with
a cloth soaked in turpentine substitute.
In order to guarantee constant readiness for operation, the
machine should be checked for worn carbon brushes at one
of the AEG after-sales service agencies.
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents (see
our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
HB 750
............13000 min
.............. 11000 min
-1
-1
Volker Siegle
Manager Product Development
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
HBE 800
-1

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Hb 750Hbe 800

Tabla de contenido